My Mitsubishi Triton trouble about SRS system with clock spring.

My Mitsubishi Triton trouble about SRS system with clock spring.

       My car showed SRS warning lamp. I use M.U.T.-III connect ecu for check error code. The result is problem at clock spring unit. The SRS-ECU diagnoses the following items and stores a diagnosis code in the non-volatile memory (EEPROM*1) when a problem is detected. Therefore, the memory is not deleted after a battery terminal is disconnected. (The diagnosis code memory can be deleted by the M.U.T.-III).

SRS warning lamp still show (Upper from Mitsubishi manual)

      If the SRS lamp still show after start engine the air bag and seat belt with pre-tensioner system will not work. So it's very dangerous when a crash.

Clock spring is??? 

     The clock spring set up between the steering column and steering wheel. And function is a special rotary electric connection between SRS ECU and air bag module. Because air bag module locate on steering wheel and it make streering wheel turn around.

Clock spring position (Mitsubishi manual)

     I change clock spring part at Mitsubishi service center. And I disassemble it shown with lower picture. The clock spring consist ribbon cable, connector and rotary part for keep ribbon cable.

Clock spring (Upper)  Inside clock spring (Lower)

Caution on clock spring
CAUTION: SRS CLOCK SPRING PLEASE DO NOT TURN EXCEPT WHEN REQUIRED. THIS IS NOT A REPAIRABLE PART. IF DEFECTIVE, PLEASE REPLACE ENTIRE UNIT ACCORDING TO THE SERVICE MANUAL INSTRUCTIONS. ALIGNMENT OF MODULES IS NECESSALY WHEN THEY ARE ADJUSTED AND/OR INSTALLED FOR THE ALIGNMENT PROCEDURES, FOLLOW THE SERVICE MANUAL INSTRUCTIONS.

Remark :When remove SRS system part must disconnect battery terminal before. 

Thank you for reading my blog. If you have any question please comment.

Join with Triton 4x4 Thailand Club : Part Record tape Guru Test Cars Variety Triton 4x4

Join with Triton 4x4 Thailand Club : Part Record tape Guru Test Cars Variety Triton 4x4
     I am member Triton 4x4 Thailand club. On saturday 23/07/11 the member in club was invited to record tape by Guru-test.com. For show Mitsubishi triton offroad car and meeting in club.

Members car to joined this even. 

    This location for make film is German brewery at Bangkok Thailand. Somebody in club he traver above 300 kilometer for joined this event. 

Misubishi triton 4x4 Thailand club

Misubishi triton 4x4 Thailand club

 Triton 4x4 Club
       The Triton 4x4 club was founded for 5 years ago. And objective for a meeting of the social activities, share knowledge and guidelines for upgrade car of user mitsubishi triton 4wd. For the website club is http://www.triton4x4club.com/ .

Tape record in youtube by Guru-test.com


Part 1 of 4

Part 2 of 4


Part 3 of 4


Part 4 of 4



Or can direct see in Guru-test website here : http://www.guru-test.com/index.php?lay=show&ac=article&Id=539171270&Ntype=2


Thank you for reading my blog. Special thank Guru-test.com and Triton 4x4 club.com. If you have any question please comment.

Step up 2 inch body for Mitsubishi L200 Triton offroad

Step easy lift up 2 inch body for Mitsubishi L200 Triton offroad.
      Today I will share method lift up 2 inch body for Mitsubishi L200 Triton with lift up body kit set high 2 inch. Those include two piece support rear spring thick 2 inch, two piece support front shock absorber thick 1 inch, spacer for ball joint upper arm and Amada Xtreme shock absorber full length 24" .

After up body 2" with Tyre Maxxis Buckshot Mudder 245/75/R16

    For front shock absorber insert support thick 1" above spring. They can lift up body to 2".  But I must front wheel alignment check and adjustment again.

Insert support thick 1" above spring

    Ball joint must support by spacer thick 1" too. Because when body lift up this point will drop down.

Spacer for ball joint upper arm

     Rear section will add support between shaft and rear spring. The support thick 2" and change U-Bolt length 18".

Insert piece support between rear spring

    And change shock absorber full length 24" brand Amada xtreme 20 mm core.

 Amada xtreme 20 mm core

     They can lift up body higher than standard 2" or 25.4 mm. 

After completed with lift up set

Thank you for reading my blog. If you have any question please comment.

D.I.Y. Connect I-Pod & I-Phone with Mitsubishi

D.I.Y. Connect I-Pod & I-Phone with Mitsubishi
          Today i will share about add port AUX for common CD player In Mitsubishi TRITON 4x4 or L200. Normally them can play CD Audio, CD MP3 and Radio. and now we will use them play sound from Portable player like that I-Pod, I-Phone and other. 

Common CD Player in Misubishi Triton

What needs to be prepared.

     1. Brass connector (3 pieces)

Brass connector

Brass connector

2. Female jack 3.5 mm with wire (1 piece)

Female jack 3.5 mm

3. Stereo Male - Male jack 3.5 mm with wire (1 Piece)

Male jack 3.5 mm

4. Electrical wire 1x1 mm (3 color about 0.5 m)

Let Start !!!
1. Removal CD Player and rear connector.

Rear connector

2. Connect electrical wire in brass connector. First color for signal L. Second color for signal  R. And last color for signal ground.


3. Connect electrical wire with brass connector in real connect follow picture

Connect wire signal in rear connector .

4. Connect electrical wire with female jack 3.5 mm.

Wire from female jack 3.5 mm.

5. Install CD Player into slot and press on button. Then press CD button about 5 second until AUX show on display.

Press CD Button 5 Sec.

AUX show on display

6. Connect male jack into female jack and other side connect with I-Pod Or I-Phone. Joy with them!!!!

Connect with I-Pod

   Thank you for reading my blog. If you have any question please comment.